Supply PC Hammer Crusher20081105

Luoyang UTURN Machinary Co., Ltd.
The PC hammer crusher crushes by the collisions between high-speed hammer and material, which features in its simple structure, high reduction rotation, high efficiency, ect.. The PC hammer crushers were developed for the both dry and wet crushing of brittle, medium-hard materials for the mining, cement, coal, metallurgic, construction material, road building, and Petroleum & Chemical industries.

Hammer crusher Application:
Hammer crusher is suitable for mid-hard and light erosive materials, whose pressure
resistance strength is no more than 100Mpa and humidity lower than 15%, suchas coal, salt, chalk, gypsum, blocks, limestone, etc.
Hammer crusher Operating Principle:
The main working part of hammer crusher is rotors with hammer. The rotors consist of main shaft, disk, pin shaft and hammers. The motor drives the rotors to rotate quickly in the crushing cavity. Raw materials enter the crusher through the feed opening and are stricken, impacted, cut and ground by the high-speed hammerto small size. There is a screening plate under the rotor, so that materials with size smaller than the screen mesh will be screened out and others are left tobe further hammered and ground until reach the standard size. The size of the final product can be adjusted by changing the screening plate. The gap between therotors and the screening plate can also be adjusted according to different requirement.
Main technical data:

Model Rotor diamete/Length
（mm） Rotate
speed
（r/min） Feed inlet
size（mm） Feed size
（mm） Discharge
size
（mm） Capacity
（t/h） Motor
Power
（KW） Weight
（T） Dimension
L X W X H      
（mm）
PC400×300 φ400/300 1200 80 10 5～8 11 0.7 812×982×758
PC600×400 Φ600/400 1000 100 15 10～15 18.5 1.5 1200×1114×1114
PC800×600 Φ800/600 980 120 15 20～25 55 3.7 2620×1864×1340
PC1000×800 Φ1000/800 980 200 45 34～54 115 6.5 3574×2250×1515
PC-42 φ400/175 1000 145×270 50 3 0.5 5.5 0.5 812×1056×1315
PC-44 φ400/400 1500 145×450 100 10 5～8 7.5 0.9 744×942×878
PC-64 φ600/400 1000 295×450 100 15 10～12 18.5 1.03 1054×972×1117
PC-66 φ600/600 1000 295×570 100 10 12～18 45 2.14 1315×840×1501
PC-86 φ800/600 1000 350×570 200 10 20～25 55 2.45 1515×2586×1040
PC-88 φ800/800 1000 350×850 200 15 35～45 55 3.05 1515×2831×1040
PC-108 φ1000/800 1000 580×850 200 13 25～40 110 6.5 3206×2210×1515
PC-1010 φ1000/1000 1000 580×1060 200 15 40～60 132 7.59 3514×2230×1516
PC-1010 φ1000/1000 1000 580×1060 200 10 30～50 160 7.59 3514×2230×1518
PC-1010 φ1000/1000 1000 580×1060 200 8 25～35 185 7.59 3514×2230×1518
PC-1212 φ1250/1250 750 650×1330 200 20 90～110 185 19.1 4475×3162×2250
PC-1414 φ1400/1400 750 1050×1540 250 20 120～170 280 17.2 2790×2800×2310
PC-1616 φ1600/1600 590 1200×1740 350 20 220～280 500 32.4 6256×3620×2700